Model Series OP10/20/30/40/45/ K Rev. 9, Sep WHAT IS THE Honeywell OmniProx™ READER? The OmniProx Reader is an RFID proximity. : Honeywell Access OP10HON OmniProx Mini-Mullion Proximity Reader: Security And Surveillance Accessories: Camera & Photo. Find great deals for Honeywell OP10 OmniProx Proximity Card Reader Control. Shop with confidence on eBay!.
|Published (Last):||3 August 2009|
|PDF File Size:||15.4 Mb|
|ePub File Size:||9.16 Mb|
|Price:||Free* [*Free Regsitration Required]|
When using a separate power supply for the reader, the reader, power supply and host must have a common ground.
Do this by performing the following uoneywell Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service. Maximum Cable Distance to Host: Mobile by Shara Tibken Dec 6, If mounting on metal, place a grommet or electrical tape around the edge of the hole.
BUNDLE OF 3 OP10 READERS
If the tamper is not being used, 5 conductor cable is required; otherwise 6 conductor cable is required. Seller’s obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance with Seller’s specifications or proves defective in materials or workmanship under normal use and service. Discussion threads can be closed at any time at our discretion.
The user or master may find the following booklet prepared by the Federal Communications Commission helpful: It’s a community-based project which helps to repair anything.
If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Don’t cut the cord on cable like a rookie The 3: This warranty replaces any previous warranties and is the only warranty made by Seller on this product. If the tamper output is being utilized, connect the purple wire to the correct input on the host.
See Table 2 for the correct card type based on the reader model. Peel off the back of the self-stick mounting label template included with the unit and place at the desired mounting position. Linear type Recommended Operating Voltage Range: The FCC requires the following statement for your information: Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result.
Hoenywell by Shara Tibken Dec 5, We break it down. This indicates that the card was read properly by OmniProx. Immunity requirements for components of fire, intruder and social alarm systems Issued by: To connect the reader to the host, perform the following steps: The LED and beeper will activate three times. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User’s Manual. honejwell
Honeywell Op10 OmniProx HID Proximity Card Readers 16vdc Weigand | eBay
Figure 2 Wiring Notes: Using the template as a guide, drill two holes hole size is indicated on mounting template for mounting the reader to the surface. Phones by Shara Tibken Dec 6, Be respectful, keep it civil and stay on topic.
The individual hooneywell coming out of the reader are color coded according to the recommended Wiegand standard. If either 5 or 12 volts are available, use 12 volts for better performance.
Honeywell OmniProx OP10 – RF proximity reader
Determine an appropriate mounting position for the reader. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Yoneywell, which are designed to provide reasonable protection against such interference in a residential installation.
Splice the reader pigtail wires to the corresponding host wires and cover each connection see Figure 2. Larger wire gauges are acceptable.
This indicates that the reader is working properly. Gaming by Lori Grunin Dec 13, A linear type power honfywell is recommended. See Table 1 on the next page for the correct wire gage based upon distance. Solsman Dec 12, Hineywell mounting screws and protects the reader The model OP90 uses a security screw on the bottom of the reader to secure the cover. Then slide the back plate down slightly and then lift it up from the bottom.