Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.
|Published (Last):||3 July 2013|
|PDF File Size:||17.89 Mb|
|ePub File Size:||3.10 Mb|
|Price:||Free* [*Free Regsitration Required]|
So now i activate the alarm on only a 3 digit code and it is working like that. The alarm was then activated, without me activating it. fbk
The keypad sounder proogram differently to indicate the following conditions: I want to change this 3 digit code to a new 4 digit code, but with no success. Section 5 – System Operations User Deletion User codes can be deleted directly through the keypad.
FBI XL-2T PC download software
See the following diagram: Page 81 – Extended 3×1 Ext. Once deleted their values will be null. Comments to this Manuals Your Name. We regret any inconvenience this may have caused and appreciate your continued support of FBII products.
FBII XL-2T Installation And Setup Manual
Section 5 – System Operations If a user code is not required to set the time, then enter: For UL installations see wiring diagram for hookup. When the switch is pushed toward the front of the keypad, in the opposite pdogram of the arrowthe switch is in the OFF position.
Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system. For Built-in Siren Driver, connect a single 8 ohm speaker only.
FBI XL-2 Program Sheet
Refer to the Installation Instructions for hookup information. If the siren is already sounding, the supervision will not take effect until cl2t bell cutoff time.
There are 36 total questions, with multiple data entry locations. For Bell Output, connect a siren driver ex: The auto arm time represents the time of day that the area will automatically arm if it is not already armed. Fni a keypad tamper code is entered then it will be transmitted to the Central Station. Upon entry to the system log view, LCD based keypads will show the events one at a time starting from the oldest event.
This equipment generates and uses radio frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer’s instructions may cause interference to radio and television reception. Page 23 Fire Trouble is reported to the CS if enabled program question 32, location 3.
I then pressed code button followed by master codethen user no 3 and then new 4 digit user code. Don’t show me this message again. The Ffbi requires the following statement for your information. The rear plastic mounting plate is not used for recessed installations.
If selected, then a negative acknowledgment 4 short beeps will be heard after attempting to enter this mode.
Upon detection of the first violation, smoke detector power on conventional 4 proggram smoke detectors connected to ZONE modules will be reset for a period of 8 seconds.
Replacement microprocessors are available through Technical Support or Customer Service. Proceed to question 02 through the sequence With this device some systems can obtain dial tone in areas which do not automatically provide dial tone.
Page 40 Section 5 – System Operations If a user code is not required to set the time, then enter: The checkmark highlights which options are selected. Good Day I had a four digit user code, but the last digit was lost.
The keypad will indicate a trouble on the fire zone if the bell or sounder is not properly connected. Programming Questions This topic defines the programming questions and the values for each question. A-2 Partial Extended 3×1 Part. I shall be pleased to learn from you in this regard.
The following is a quick comparison. Each condition will cause these LEDs to operate differently as follows: Quick Arming allows arming the system without entry of a user code and will report as user LCD display keypads will indicate ptogram following message: Question 32, L1 – Bypass Code Section 5 – System Operations 4.
This will be used by the CS downloading computer to determine the proper account information to download to this subscriber. Enter text from picture: System Programming Programming Questions This topic defines the programming questions and the values for each question.
This enables Fire and Burg zones to provram restores. The system contains up to fifteen user codes 4 digits each with the following applications: System ready to be armed System not ready to be armed