ASTM D The Bulk Density Tester series testers are used to measure apparent density, bulk factor, and. RAW MAteRiAL evALUAtion. ASTM D METHOD A. Primarily used to measure the apparent density of fine granules that can be poured readily through a “v”. ASTM D , ISO R Food Testing, Other Applications Testing, Plastic Testing . Plastics and Resins. Density and Specific Gravity. A bulk density tester does.
|Published (Last):||3 March 2012|
|PDF File Size:||11.62 Mb|
|ePub File Size:||6.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
Specifications Measuring funnel Weight plunger Lead shot Tests that can be conducted are: Also, since they ordinarily are very bulky when loosely pouredand since they usually are compressible to a lesser bulk, evenby hand, a measure of their density under a small load isappropriate and useful.
Originally approved in Last previous edition approved in as D 96 Lead shot is used to increase the 1d weight to g to compress the material under test. Open thebottom of the funnel quickly and allow the material to flowfreely into the cup. This standard has been approved for use by agencies of the Department of Defense.
Calculate the weight in grams of 1 cm3 of the material.
For coarse flakes, strands, chips and cut fibres that cannot be poured using test methods A and B Ray-Ran offer a measuring cylinder and plunger to method C of the ASTM test standard.
When the latter method is used, the average speci? We have no amendments or corrections for this standard. The weight per unit volume of a material, including voids inherent in the material as tested is apparent density.
A bulk density tester does not measure an intrinsic property of a material; Bulk density can change depending on how the material is handled. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This edition includes the addition of an extensive ISO equivalency statement and keywords section. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The total volume includes particle volume, inter-particle void volume and internal pore volume.
The aztm in parentheses are for information only. Allow the weight to settle for 1 min and take the reading from the scale to the nearest 0. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
LABULK Plastics Moulding Materials Apparent Density Tester︱Funnel︱ASTM D A | AimSizer
Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. For coarse flakes, strands, chips and cut fibres that cannot be poured using test methods A and B Ray-Ran offer a measuring cylinder and plunger to method C of the ASTM test standard. Carbon black is a material that may be premixedwith the sample at concentrations of 0.
With the apparatus assembled as shown in Fig. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. If caking occurs in the funnel, the material may be loosened with a small glass rod. NOTE 7—Because bulk factor is a dimensionless ratio, it permits ranking of plastic materials, with respect to volume change upon fabrication, regardless of their molded or formed density or speci?
This standard has been approved for use by agencies of the Department of Defense. Lower this weight gradually into the measuring cylinder until it is entirely supported by the material.
This edition includes the addition of an extensive ISO equivalency statement andkeywords section. Densidad aparente y modulo de finura Documents. The bulk factor is also equal to the ratio of the density after molding or forming to the apparent density of the material as received.
Current edition approved Jan. Permission rights to photocopy the standard may also be secured from the ASTM website www. This reading will give directly in centimetresthe height, H2, of the material.
Densidad Aparente y Mtodos para determinar Documents. Such materials cannot bepoured through the funnels described in Test Methods A and B. Lead shot is used to increase the plunger weight to g to compress the material under test.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. To avoid this, the cm3 cup shown in Fig. Allow the weight tosettle for 1 min and take the reading from the scale to thenearest 0.
ASTM D1895 (Densidad aparente).pdf
Loosely drop 60 6 0. The bulkfactor is also equal to the ratio of the density after molding orforming to the apparent density of the material as received. Reload Image Please enter the letters from the image: To convert grams per cubic centimetre to pounds per cubic foot,multiply by